Nostr notes by Ian Dunn

That's a good find. A gold plated usbc, now I've seen it ...

2026-07-30T00:51:05Z

In reply to nevent1q…ly06
_________________________

That's a good find. A gold plated usbc, now I've seen it all.

Yea I think that's the same thing. Neat!

2026-07-28T03:14:54Z

In reply to nevent1q…2454
_________________________

Yea I think that's the same thing. Neat!

Yes it works just fine. I find that unless you're board is ...

2026-07-24T12:12:16Z

In reply to nevent1q…qqwq
_________________________

Yes it works just fine. I find that unless you're board is something that is not electrical then there's no need for a schematic but not skipping the schematic will probably save you having to revise and re order your pcb if it's got any electrical functionality.

I've had success swapping two adjacent pins by bending one ...

2026-07-23T23:53:54Z

In reply to nevent1q…7c30
_________________________

I've had success swapping two adjacent pins by bending one pin up in the air and the other pin way over to the adjacent pad. Then use a resistor lead or something simmilar to connect the pin this up in the air to its pad.

been there, done that!

2026-07-23T23:46:40Z

In reply to nevent1q…7c30
_________________________

been there, done that!

Are you cowdfunding something?

2026-07-22T12:40:32Z

In reply to nevent1q…7f68
_________________________

Are you cowdfunding something?

That's a good idea. I'll bet the power supply works. I ...

2026-07-19T21:47:24Z

In reply to nevent1q…w4rd
_________________________

That's a good idea. I'll bet the power supply works. I think I'll dig into this sometime on a holiday when I need a project.

Thanks, that's good to know. That's shouldn't be very ...

2026-07-19T21:15:57Z

In reply to nevent1q…zf8v
_________________________

Thanks, that's good to know. That's shouldn't be very difficult to fix. I did notice a faint intermittent sound coming from the power supply, like it was overloaded and shutting itself off, then trying again about 2 seconds later. That adds up with the shorted tantalum caps. Thanks for the picture!

Yea that's what I was thinking. I'm guessing I'll ...

2026-07-19T21:07:30Z

In reply to nevent1q…ahm4
_________________________

Yea that's what I was thinking. I'm guessing I'll have to replace every aluminum electrolytic and tantalum capacitor.

I just rescued this Compaq Portable II computer from the E-scrap ...

2026-07-19T20:57:22Z

I just rescued this Compaq Portable II computer from the E-scrap pile at my local transfer station. I managed to snag 2 of 4 of them before I got chased away by the staff. No scavenging allowed. It's eating me alive thinking about the other cool stuff including 1 more of these computers that are still sitting there. At least I was able to snag 2 of them. It didn't power on, I suspect the capacitors will have to be replaced. Has anybody ever had any luck reviving one of these?

#vintagecomputing

When it comes to board games and most competitions, I'm ...

2026-07-18T19:41:02Z

In reply to nevent1q…748u
_________________________

When it comes to board games and most competitions, I'm always the first to loose. But this is my kind of competition! I'm sorry I'm not there.

I made this cool little binary clock on a whim. It was so easy it ...

2026-07-18T02:53:49Z

I made this cool little binary clock on a whim. It was so easy it felt like cheating. It's got an Atmel 328PB for a brain, a DS1307 real time clock, and a string of 19 WS2812 addressable LEDs to display the time. I also added a switch to toggle between 12 and 24 hour modes. Sandwitched between the two PCBs is a coin cell that powers the RTC when its un-plugged, so you dont have to set the time every time you plug it in. It took about 5 minutes to write the firmware with AI and it worked on the first try. I made a YouTube video showing each step of the process, and I have my open source design is free for the taking on my website. I'll sell complete clocks as soon as I get more 328PB micro controllers.

Youtube video: https://youtu.be/NYM3-Beix3Q

Open Source Design:
https://www.boltind.com/binary-clock-with-ws2812-addressable-leds-and-microcontroller/

#Electronics #Binary_Clock #DIY_Clock

Thanks for sharing. I love these naked pictures!

2026-07-17T16:46:37Z

In reply to nevent1q…wmma
_________________________

Thanks for sharing. I love these naked pictures!

absolutely beautiful!

2026-07-17T16:34:18Z

In reply to nevent1q…7062
_________________________

absolutely beautiful!

Thanks Carrie! I'm seeing all sorts of posts about Teardown ...

2026-07-17T03:56:09Z

In reply to nevent1q…hedx
_________________________

Thanks Carrie! I'm seeing all sorts of posts about Teardown and Defcon and I'm totally feeling sorry for myself because I can't be there. I hope your talk goes well and you have a great time!

I wish I could be there! I'll defenantly watch your talk from ...

2026-07-16T15:00:30Z

In reply to nevent1q…7xky
_________________________

I wish I could be there! I'll defenantly watch your talk from here if it's recorded.

Thanks!

2026-07-16T14:58:55Z

In reply to nevent1q…t94w
_________________________

Thanks!

@npub13e2…n8tx Here's another one for you. This is a PCB ...

2026-07-16T01:53:31Z

meek cynics (npub13e2…n8tx) Here's another one for you.

This is a PCB that I ripped out a thirty something year old ATM I pulled out of the trash. Way too beautiful for the landfill! The second photo is the same PCB taken with my cell phone. The right camera, lens and lighting make quite a difference! I took this with my Olympus D E M5 MARK III and a M.Zuiko ED 30mm F3.5 macro lens. This is a raw image, I don't use any post processing.

#electronics #photography #macro_photography #PCB_art

I spitted the #mnt_reform Next laptop on crowdsupply about a week ...

2026-07-15T21:21:13Z

I spitted the #mnt_reform Next laptop on crowdsupply about a week ago and I am really tempted to sign up for one. I love the modular design, the hackability and the georgeous CNC aluminum case. My only real hesitation is that I could get a much faster Framework laptop for the same money. Framework is repairable, but nowhere near as cool as the MNT. Does anybody out there have any experience with the MNT's SOM module, the #RK3588 as a daily driver? I'm a lifelong Ubuntu user. It sounds like Debian is better fit for this SOM, and I don't think I'd mind switching. I do occaisional video editing. Has anybody out there experemented with Kdenlive on Debian (or ubuntu) with the RK3588? Or have an opinion about the MNT laptop?

Haha I love it! Honestly that may just be my favorite song. I ...

2026-07-15T04:15:52Z

In reply to nevent1q…tqjk
_________________________

Haha I love it! Honestly that may just be my favorite song. I listen to that soundtrack while I'm taking pictures and making artwork!

This is super cool! I'd like to see some more about your ...

2026-07-14T12:20:15Z

In reply to nevent1q…0y6d
_________________________

This is super cool! I'd like to see some more about your process and the boards you've made!

I've played with those, they are really nifty.

2026-07-13T16:28:09Z

In reply to nevent1q…c4nh
_________________________

I've played with those, they are really nifty.

I hope you have a great vacation.

2026-07-13T11:55:27Z

In reply to nevent1q…tt4z
_________________________

I hope you have a great vacation.

Another one finished! I could use some help with a name for it. ...

2026-07-12T22:39:19Z

Another one finished! I could use some help with a name for it. It's an eyeball. The outside is dark American Walnut, and it's supposed to represent the natural world. The inside is a circuit board, representing technology. I don't think it is too far fetched that people will have cybernetic eyeballs in the coming decades. The idea of a cybernetic eyeball is what inspired this piece. Most of the components on the pcb are for looks, but there's a string of ws2812 leds that I designed to look like Ethernet link lights.

#PCBArt #TechArt #ElectronicArt #LEDArt #SciFiArt #Singularity# PostSingularity #Cybernetic #CreativeCoding #Transhumanism #electronics

That's what everybody says, but unfortunately I have to take ...

2026-07-12T13:58:27Z

In reply to nevent1q…gzl7
_________________________

That's what everybody says, but unfortunately I have to take out the guts to make room for the clock.

Haha! I can't argue with that. Good point! Lol.

2026-07-12T13:57:20Z

In reply to nevent1q…ktce
_________________________

Haha! I can't argue with that. Good point! Lol.

I got started with Easy EDA and switched to kicad. I'd say ...

2026-07-11T18:40:37Z

In reply to nevent1q…vvee
_________________________

I got started with Easy EDA and switched to kicad. I'd say that kicad has a slightly steeper learning curve but it's totally worth the effort. For board outlines my approach is to draw a square and change it to the edge.cuts layer. For anything more complicated than that I usually draw the outline in Inkscape and import it to kicad. Kicad does a great job of importing vector graphics.

Here's a #NixieTubeClock that I made. I just love these old ...

2026-07-11T13:56:49Z

Here's a #NixieTubeClock that I made. I just love these old Weston meters. They mostly sin in basements where nobody gets to appreciate or enjoy them. I think they are absolutely gorgeous. What better way to make them useful again by turning them into a Nixie clock? This one had a resistor in the top that apparently needed all those little holes to dissipate heat, so I stuck a Bluetooth speaker in there too. #electronics #clocks #steampunk

Thanks Dade!

2026-07-11T04:43:02Z

In reply to nevent1q…crnp
_________________________

Thanks Dade!

Thanks! I'm glad you're enjoyoyng them. Yea, they are ...

2026-07-10T18:07:56Z

In reply to nevent1q…wj3z
_________________________

Thanks! I'm glad you're enjoyoyng them. Yea, they are real images scratches and all. I do these in a pitch black room, camera on a tripod and all of the light is from the LED lights that I can precisely control. They are focus stacked with as many as 15 different images. The aperture still needs to be really small to get a sharp focus, so the shutter speed needs to be fairly long, so I need really precise control of the light. I usually have 1 or 2 colors, plus a white light. It's been a very long time in the making, but I finally started a youtube channel. I defenantly plan on making a video explaining how I make these images.

Here's today's circuit board picture. I use a few LED ...

2026-07-10T15:49:53Z

Here's today's circuit board picture. I use a few LED lights and focus stacking to get these images. I took this with my Olympus D E M5 MARK III and a M.Zuiko ED 30mm F3.5 macro lens. This is a raw image, with no post processing. I've got a years long backlog of these images I've never shared before. More coming soon. #electronics #photography #macro_photography #PCB_art

with the empty traces? I turned that on by mistake once. I ...

2026-07-09T22:06:08Z

In reply to nevent1q…eeue
_________________________

with the empty traces? I turned that on by mistake once. I didn't care for it.

Yes. This is a fairly old board that has those very unusual ...

2026-07-09T18:28:51Z

In reply to nevent1q…052g
_________________________

Yes. This is a fairly old board that has those very unusual square vias. they are absolutely gorgeous lit up from the bottom!

Circuit boards have a certain beauty that rarely gets ...

2026-07-09T17:54:30Z

Circuit boards have a certain beauty that rarely gets appreciated. With the right lighting and the right lense they look like a busy city street. I took this with my Olympus D E M5 MARK III and a M.Zuiko ED 30mm F3.5 macro lens. This is a raw image, i didnt use any post processing. Follow me if you want to see more! #electronics #photography #macro_photography #PCB_art

Thanks!!! I'm trying to get better about this social media ...

2026-07-08T23:17:01Z

In reply to nevent1q…pntj
_________________________

Thanks!!! I'm trying to get better about this social media stuff. I just recently signed up for Mastodon and I really like it. I've got a years long backlog of stuff I've never shared with the internet so I'm trying to post here regularly. If you want to see more I have some of my art on my website: www.iandunnart.com and my (not art) electronics stuff on my other website, www.boltind.com.

I think maybe once a year I order a #PCB and it's perfect on ...

2026-07-08T23:11:28Z

I think maybe once a year I order a #PCB and it's perfect on the first try. That just happened to me with this project. I don't have anything to change on my board layout and my AI coded firmware worked perfectly on the very first shot. This christmas tree is one of several circuit board christmas ornaments I'm working on. I'll have them for sale in about October. The brain is an atmel 328pb microcontroller and the leds are ws2812-2020. Most of the other components are decorative.

Thanks!!!

2026-07-08T22:56:01Z

In reply to nevent1q…a5uz
_________________________

Thanks!!!

Hey Dade, Sorry for the confusion. I put them in my Etsy store. ...

2026-07-06T11:47:32Z

In reply to nevent1q…lwz8
_________________________

Hey Dade, Sorry for the confusion. I put them in my Etsy store. https://www.etsy.com/shop/BoltIndustriesPCB

I’m really excited to share a piece of art that’s been two ...

2026-07-06T03:09:57Z

I’m really excited to share a piece of art that’s been two years in the making. I call it Algorithmic Precipitation.

The piece is built from a custom printed circuit board. In the top copper layer is a city intersection, with a woman crossing the street. An everyday moment from a future that hasn’t quite arrived yet.

Across the scene, a downpour of small green raindrops falls from the sky, rendered using a grid of WS2812-2020 LEDs controlled by an ATmega328PB microcontroller. Two white LEDs occaisionally flash like lightning. A single amber LED mimics a failing streetlight.

The work is an exploration of what a post-singularity world might look like, where the boundary between the natural world and technology has blurred, and both are part of the same evolving system.

Also, I am trying to get better at this social media stuff, so today I uploaded my first YouTube video! If you want to see more of this piece, I made a long form video detailing every step of how I made it. Likes, boosts, and subscribers are appreciated! Check it out here: https://youtu.be/k712ZmR4pAk?si=-9bLeB-qkFdm6Kyn

I also have more pictures on my website: www.iandunnart.com.

#PCBArt #TechArt #ElectronicArt #LEDArt #SciFiArt #Singularity #PostSingularity #Cybernetic #CreativeCoding #Transhumanism #electronics

I found this Peerless Switch Dial Testing set on eBay a while ...

2026-06-24T04:18:29Z

I found this Peerless Switch Dial Testing set on eBay a while back. I think it's some sort of telephone industry tool. I gave no idea how it works. My intention was to gut it and turn it into a nixie clock, but I just don't think I have the heart to do it. It's just too cool as it is. Does anybody know what it's for? It feels heavy enough that it must have a transformer inside.